AC/DC Adapters
AC/DC Adjustable Power Adapter Supply 4-24V 2.5A 60W Speed Control Volt Display EU/US/AU/UK Plug
Questions and Answers
What is the diameter of the connecter?
Staff told me it's 5.5 X 2.5 mm
What about jack diameter?
5.5 X 2.5 mm, according to site staff
Reviews
Peter
on 19 May 2021
go my Order. Easy to adjust from 3 Vto 24V. 50cm Power Cable only. Im fine with it. Shipping takes 6 days to Germany from CZ Warehouse. even it was mentioned 1 to 3 days. im fine with it. Price was 9,92€ Euro. Lets see how it will work.
Valtinho29
on 10 December 2020
I'll test it yet, but it seems all right
pincopinco
on 24 February 2020
I bought it for $11.42 Delivery to Ukraine in 34 days (it was during the virus epidemic in China). Min output voltage 3.37V Maximum output voltage 24.7V In general, the device is quite good, but there are a couple of drawbacks: the cable is not heat resistant, does not withstand 200°C (not tried below). Short cable inlet - 50cm.
valius
on 30 January 2019
Good power supply. Adjustable from 3.5V to 24.5V. PCB looks good, but be better soldered. HOT side PWM controller CR6850 (smd sot-23-6), power mosfet CDT6N60. Capacitors 47uF400V+10uF400V. Cold side diode STPR1020, 680uF35V *2. and AZ431AN shunt regulators.
hf-seeker
on 08 December 2018
I have determined the following parameters for the supplied power supply, bottom stop: measured 3.37V, display 3.39V, no-load losses 0.14W top stop: measured 24,21V, display 24,9V, no-load losses 0,84W The ripple is considerable with about 420mV, especially in the lower voltage range. There are also much stronger needle pulses. The output circuit is therefore insufficiently filtered. I found an efficiency of just over 86%, at 24V and 40W. My measuring equipment for this are not so accurate. I would not use the power supply for computer technology. It can be used for electronics experiments above 5V and for the supply of smaller AF power amplifiers. But you should provide an additional support capacitor. Bei der gelieferten Stromversorgung habe ich folgende Parameter ermittelt, unterer Anschlag: gemessen 3,37V, Anzeige 3,39V, Leerlaufverluste 0,14W oberer Anschlag: gemessen 24,21V, Anzeige 24,9V, Leerlaufverluste 0,84W Die Welligkeit ist mit etwa 420mV erheblich, insbesondere im unteren Spannungsbereich. Es treten auch noch wesentlich stärkere Nadelimpulse auf. Der Ausgangskreis ist demnach unzureichend gefiltert. Ich habe einen Wirkungsgrad von etwas über 86% ermittelt, bei 24V und 40W. Meine Messmittel hierfür sind aber nicht so genau. Die Stromversorgung würde ich nicht für Computertechnik einsetzen. Sie ist einsetzbar für Elektronik-Experimente oberhalb 5V und zur Versorgung von kleineren NF-Endverstärkern. Einen zusätzlichen Stütz-Kondensator sollte man aber vorsehen.
Herbert Dobsak
on 19 November 2018
and my quick test with 24.5 V on a 11.2 Ohm resistor results in 2.22 Amp. (24.5/11.2 = 2.12 Amp). The power supply unit is good.
dnomikos
on 08 October 2018
Excellent quality at excellent price. Very accurate workbench DC power supply. I'm very pleased :)
Preetsui
on 30 September 2018
Highly Recommended - Small Compact Size - Very Usefull - Working Perfectly - Go For It
pagan
on 27 August 2018
Подключил к блоку питания монитор на 12В 2А, он заработал. Без нагрузки индикатор на БП отображает 3,33В (мин.) и 24,5В (мах). Длина шнура от вилки 220В до БП 114 см, от БП до цилиндрического разъема - 60 см. Оба провода мягкие. Есть четыре отверстия для крепления к плоской горизонтальной поверхности. Устройство оставило положительные впечатления.
abogassar
on 06 June 2018
محول من ٣.٣ فولت الى ٢٥ فولت تقريبا ممتاز جدا وانصح به
